|
|
|
|
KINS-LA의 구성 |
|
Insulating Gasket |
Insulating Sleeve |
Insulating Washer |
Metal Washer |
|
|
|
|
Insulating Core Material - GRE NEMA G-11 Sealing Material - Neoprene Rubber
|
Insulating Material - GRE NEMA G-11
|
Insulating Material - GRE NEMA G-11
|
Zinc-Plated Steel - Carbon Steel
|
|
|
KINS-LB의 구성 |
|
Insulating Gasket |
Insulating Sleeve |
Insulating Washer |
Metal Washer |
|
|
|
|
Insulating Core Material - Cotton Cloth Phenolic Sealing Material - Neoprene Rubber
|
Insulating Material - Cotton Cloth Phenolic
|
Insulating Material - Cotton Cloth Phenolic
|
Zinc-Plated Steel - Carbon Steel
|
|
|
|
|
|
|
KINS-HA의 구성 |
|
|
|
|
|
Metallic Core - SUS316L Insulating Material - GRE NEMA G-11 Sealing Material - PTFE with Spring-Energized
|
Insulating Material - GRE NEMA G-11
|
Insulating Material - GRE NEMA G-11
|
Zinc-Plated Steel - Carbon Steel
|
|
|
KINS-H□ Series 의 구성 |
|
|
Metallic Core - SUS316L
|
Insulating Material - GRE NEMA G-11
|
Sealing Material - PTFE
|
|
Metallic Core - SUS316L
|
Insulating Material - GRE NEMA G-11
|
Sealing Material - Graphite
|
|
Metallic Core - SUS316L
|
Insulating Material - GRE NEMA G-11
|
Sealing Material - Hollow Metal O-Ring
|
|
Metallic Core - SUS316L
|
Insulating Material - GRE NEMA G-11
|
Sealing Material - Spiral Wound Gasket
|
|
Insulating Material - GRE NEMA G-11 -Cotton Cloth Phenolic
|
|
|
|
|
|
|
- 전기적 보호가 필요한 Flange의 절연 - 서로 다른 Material를 사용하여 접촉부식(Galvanic Corrosion)을 방지하기 위한 절연 - 서로 다른 Type Flange의 사용 시 절연( RTJ to RF Flanges ) - Insulating Sleeve와 Washer의 경우 특수 재질을 사용한 Flange에 일반적인Bolt/Nut(A193 Gr.B7 / A194 Gr.2H)를 사용하는 경우 Flange의 부식 방지를 위해 사용되기도 한다. |
|
Ex.> Flange : Inconel 625 Gasket : Inconel를 사용한 Spiral Wound Gasket Bolt/Nut : A193 Gr.B7 / A194 Gr.2H Insulating Sleeve : GRE NEMA G-11 Insulating Washer : GRE NEMA G-11 Metal Washer : C/S |
|
|
|
1. Gasket 1) Core Material 각각의 Gasket에 적용되는 Core는 기본적으로 Stainless Steel , Epoxy 및 Phenolic을 사용하며, 주문자의 의한 특별한 요구 시 특수 자재의 제작도 가능 하다.
|
|
2) Physical Properties of Laminate Material & Insulation Gasket |
|
ASTM |
Test Method |
Unit |
Epoxy Glass NEMA G-10 |
Epoxy Glass NEMA G-11 |
Phenolic |
D149 |
Dielectric Strength |
Volts/mm |
550 |
550 |
500 |
D695 |
Compressive Strength |
N/mm2 |
345 |
345 |
172 |
D570 |
Water Absorption |
% |
0.1 |
0.1 |
1.6 |
D257 |
Insulation Resistance |
MΩ |
2 x 105 |
2 x 105 |
4 x 104 |
D638 |
Tensile Strength |
N/mm2 |
310 |
350 |
138 |
D785 |
Hardness RockWell -"M" |
- |
115 |
115 |
85 |
D256 |
IZOD Impact Strength |
J/m |
747 |
800 |
64 |
Temperature Range |
℃ |
Cryogenic ~ 138 |
Cryogenic ~ 176 |
-30 ~ 100 |
|
|
3) Seal Material |
|
CR ( Neoprene ) : - 40 ~ 120 ℃ -오존과 실외 환경에 있어 NR, SBR보다 더 좋은 내력을 가지며, 석유류(petrol), 광물류(mineral oils), 탄화수소(hydrocarbons)에 다소간 저항력이 있음. Nitrile Rubber ( NBR ) : - 40 ~ 120 ℃ - 광물류(Mineral oils), 방향족 지방성 탄화수소(Aromatic and Aliphatic Hydrocarbons) 과 Alcohol 에 좋은 저항력을 가짐. Ethylene Propylene Rubber ( EPDM ) : - 50 ~ 150 ℃ - EPDM은 좋은 기계적 특성을 가지며, 노화에 따른 성질변화가 적고, 오존 산소 수증기 및 물 등 실외환경에서 좋은 저항력을 가지지만, 석유류에서의 사용은 적당하지 않음. FKM ( Viton ) : - 40 ~ 250 ℃ - 우수한 내화학성을 가지며, 비교적 고온 및 방향족 탄화수소계 에서도 좋은 저항력을 가짐. PTFE - PTFE단독으로 적용 하며, Flange 하중 및 Bolt Torque 에 대한 반발탄성을 이용한 Spring-Energized Seal 형태로도 적용이 가능함.
|
|
2. Insulating Sleeve Insulation Kit에 적용되는 Sleeve는 아래에 명기된 Material로 제작 가능 하다. 제품의 Thickness는 0.8~1.0mm로 제작이 되며, Gasket이 적용되는 Flange의 Bolt에 따라서 ID 및 OD가 결정 된다. Epoxy Glass NEMA G-11 Epoxy Glass NEMA G-10 Phenolic PTFE PE
|
|
3. Insulating Washers Insulation Kit에 적용되는 Insulating Washer는 아래에 명기된 Material로 제작 가능 하다. 제품의 Thickness는 3.0mm로 제작이 되며, Gasket이 적용되는 Flange의 Bolt에 따라서 ID 및 OD가 결정 된다. Epoxy Glass NEMA G-11 Epoxy Glass NEMA G-10 Phenolic PTFE
|
|
4. Metal Washer 제품의 Thickness는 3.0mm로 제작이 되며, Gasket이 적용되는 Flange의 Bolt에 따라서 ID 및 OD가 결정 된다. ASTM F436 : Standard Specification for Hardness Steel Washers Hardness 및 도금은 ASTM F436에 기준하여 제작되며, Thickness 및 OD / ID는 당사에서 규정한 제품 치수로 제작 된다.
|
|
5. Bolt / Nut A193 Gr.B7 / A194 Gr.2H Note. 주문자의 요구에 따라 특수 재질을 이용하여 제작 가능하다.
|
|
|